Plumbing Basics: Before Bathtub Installation
Plumbing Basics: Before Bathtub Installation
Blog Article
The content following next about Tools You Need to Install a New Bathtub is particularly fascinating. You should check this stuff out.
Installing a bath tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately difficult project. If the old bathtub is easily obtainable, the project can move easily; if you have to open up a wall to eliminate the old tub and also place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need a helper to leave the old tub and set in the new one. Make sure you have certified yourself for the job as well as are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed project, it is far better to think about utilizing one before you start. Chances are you may require an expert plumber to make tube connections.
This short article will aid you install a brand-new tub in your shower room if you have actually currently purchased a brand-new bathtub and do not require to alter the arrangement of your previous water supply pipes.
Your devices as well as product checklist should comprise the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain any water staying in the system. The procedure of removing the existing taps can be rather troublesome because of the limited gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before proceeding to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in position with the manufacturer provided backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The former type must be attached to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the required position. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the bathtub up until the spirit level checks out degree.
To install faucets, fit the bottom of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water system as well as examine all joints and brand-new pipework for leakages as well as tighten them if required. Fill up the bathtub and also inspect the overflow electrical outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the tub ought to wait until the tub has been made use of at the very least once as this will certainly settle it right into its final placement.
Preparing for the Installment
First of all, the sustaining frame provided with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the versatile tap ports to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to break a stiff seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, resulting in problems with moisture and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, as well as can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to enable the movement experienced when the tub is in use. The sealant can fracture relatively very early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our section on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read through our blog. Sharing is nice. Helping people is fun. We recognize the value of reading our article about Installing A Bathtub.
Recurring Service Plans Report this page